Heating, cooling and heat pumps Concord

Heating and cooling Concord homes, sized to a 95-degree design day

Concord heating and cooling work starts from numbers the state publishes for the city itself. The Energy Code's reference table gives Concord a 1.0 percent cooling design temperature of 95°F and a winter median of extremes of 27°F, the values a load calculation must use. Every Concord ZIP is in climate zone 12, so replacing an air conditioner brings refrigerant charge and duct leakage tests by an independent rater.

The street clock at Todos Santos Plaza in downtown Concord
The street clock at Todos Santos Plaza in downtown Concord. Photo: Geraoma, Public domain, via Wikimedia Commons.

The houses here

A valley that swings 34 degrees on a summer design day

Joint Appendix JA2, the Energy Code's table of design weather, gives Concord an outdoor daily range of 34°F, a 0.1 percent cooling temperature of 102°F and 3,035 heating degree days. A load calculation uses the 1.0 percent value, 95°F with a 67°F wet bulb, may not size heating below the 27°F winter median of extremes, and fixes the indoor cooling design temperature at 75°F. Where airflow is not field-verified at 350 cfm per ton, the code also caps system capacity in an alteration, so a contractor cannot simply round up for hot afternoons.

  • Free to request, no obligation to hire
  • Up to five local pros who take this work can reply
  • Rules on this page checked against 11 public sources, November 2026
Cooling design day
95°F dry bulb, 67°F wet bulb (1.0 percent, Joint Appendix JA2)
Heating design floor
27°F winter median of extremes; 3,035 heating degree days
Energy Code zone
Climate zone 12 for ZIP codes 94518 to 94521
Gas furnace rule
Air District Rule 9-4 zero-NOx date of 2029, at replacement

The work

Concord HVAC calls and the test or rule each one sets off

  • Only the outdoor unit

    The Energy Commission's own example says replacing just the outdoor unit triggers duct sealing and verification. The ducts must test at 10 percent leakage or less of system airflow, or 7 percent to outside; failing both, every accessible leak is sealed and checked by visual inspection and smoke test. In zone 12 the new refrigerant component also needs refrigerant charge verification, a minimum airflow of 300 cfm per ton, and a digital setback thermostat.

  • A furnace and coil in the garage

    When altered ducts, an air handler, coils or plenums sit in a garage, the ducts there must reach 6 percent leakage or less, verified by an ECC-Rater, or every accessible leak in the garage must be sealed and checked by visual inspection and smoke test. The rule applies to any length of new duct in the garage, and sampling is not allowed: each house gets its own inspection.

  • Swapping a gas furnace for a heat pump

    The Air District's Rule 9-4 sets 2029 as the zero-NOx date for gas furnaces and applies only when a furnace is replaced; its staff expect heat pump systems to be how owners comply. A heat pump needs refrigerant charge verification in every climate zone. Electric resistance cannot become the primary heat unless the old system was also electric resistance and either the new one is not ducted or no ducted cooling is being installed.

  • New ducts through the attic

    More than 25 feet of new duct brings sealing and leakage testing, and ducts in unconditioned space need R-8 insulation in zone 12. An entirely new duct system must test at 5 percent leakage or less and meet the filtration and fan airflow rules; with the air handler and ducts in a vented attic, the attic insulation and air-sealing requirements can apply as well.

Free, no obligation. Next, add your details in the request form.

Neighbourhood by neighbourhood

Parts of Concord that change an HVAC plan

  1. Holbrook

    The city's association map counts 967 homes in Holbrook, and its flood layer crosses the area with narrow strips of FEMA Zones AE and AO. Where HVAC work is part of a substantial improvement, federal floodplain rules require equipment designed or placed to keep floodwater out, so the height of the outdoor unit's pad becomes part of the plan.

  2. Canyon Creek

    Nearly all of this 104-home association is mapped High for fire hazard, next to State Responsibility Area land. A complete system replacement must carry the Energy Code's MERV 13 filtration anyway, and a house this close to the wildland edge is a good reason to confirm the filter and return are sized for it.

  3. Live Oak

    A High fire strip and a narrow FEMA Zone AE band both cross this association on the city's maps. The flood band affects where an outdoor unit can sit in a substantial improvement; the fire edge is one more reason to ask for the MERV 13 filtration a complete replacement must have.

Free request

Describe the heat pump and HVAC job once. Local pros who take work in Concord reply by call or text.

  • No fee to request, and no obligation to hire
  • You agree scope and price with the pro you choose
  • Photos help them quote without a first visit

Get quotes for heat pump and HVAC work in Concord

Two short steps. A local pro who takes this work calls or texts you back.

To send a request, call or text (415) 449-8213.

Free to request, and you agree the scope and price with the person you hire before work starts. In California, a job over $1,000 in labor and materials, or one that needs a building permit, must be done by a contractor licensed by the CSLB in the right class. Ask for the license number and check it at cslb.ca.gov.

Permits and local rules

What the Air District and the Energy Code ask of a Concord system

  • Air District Rule 9-4, gas furnaces

    The Air District's 2023 amendments set zero-NOx standards for natural gas furnaces under 175,000 BTU per hour, with a 2029 compliance date. They apply when equipment is replaced, not to a working furnace. Staff are to report on market readiness to the Board on December 2, 2026, and their November 2026 report recommends further changes and flexibilities, with amendment work beginning in 2027.

    Source: Bay Area Air Quality Management District (baaqmd.gov)

  • Altered systems under Section 150.2(b)

    Replacing an air handler, a split system's outdoor unit, a complete packaged unit or a coil requires duct sealing verified by an ECC-Rater, except for ducts already tested, systems with less than 40 feet of duct, or ducts containing asbestos. Air conditioners in zones 2 and 8-15, which takes in Concord's zone 12, and heat pumps in every zone need refrigerant charge verification.

    Source: California Energy Commission (energy.ca.gov)

  • Design conditions from Joint Appendix JA2

    Section 150.0(h) requires heating and cooling load calculations. The Energy Commission's manual says the cooling design temperature must be the city's 1.0 percent dry bulb and mean coincident wet bulb, and heating may not use a temperature below the winter median of extremes. The 2025 Joint Appendices list Concord at 95°F and 67°F for cooling and 27°F for heating.

    Source: California Energy Commission (energy.ca.gov)

State license for this work: C-20 Warm-Air Heating, Ventilating and Air-Conditioning, C-4 Boiler, Hot Water Heating and Steam Fitting, C-10 Electrical. Look up a contractor's license on the CSLB website (cslb.ca.gov).

Before you hire

Before a Concord heating and cooling bid is signed

  • Check the C-20 license at cslb.ca.gov, and a C-10 Electrical license for any new circuit a heat pump needs.
  • Ask to see the load calculation and confirm it uses Concord's JA2 values: 95°F and 67°F for cooling, 27°F for heating.
  • Ask who books the ECC-Rater for the duct leakage and refrigerant charge tests, and what happens if the ducts fail.
  • If the furnace or ducts are in the garage, ask how the work reaches the 6 percent leakage limit there.
  • In Holbrook's flood strips, ask where the outdoor unit will sit relative to the flood elevation.

Timing

The December 2 furnace briefing, and dates that move

Air District staff are scheduled to brief the Board on December 2, 2026 on whether the market is ready for the 2029 furnace standard. Dates can shift: on November 4, 2026 the Board moved the water heater standard to January 1, 2028 and added exemptions. The furnace rule still applies only when a furnace is replaced, so a working unit can stay in place while the dates settle.

Free, no obligation. Next, add your details in the request form.

Questions

Concord heating and cooling questions, from ducts to the 2029 date

Do my ducts have to be tested if only the outdoor AC unit is replaced in Concord?

Yes. The Energy Commission's manual answers exactly this: replacing the outdoor unit, or the indoor unit, by itself triggers duct sealing and verification. The exceptions are ducts already sealed and tested by a rater, systems with less than 40 feet of duct, and ducts containing asbestos. In climate zone 12 the new refrigerant component also needs its charge verified.

When does the Air District's furnace rule reach Concord homes?

Its zero-NOx standard for gas furnaces under 175,000 BTU per hour takes effect in 2029 and applies when a furnace is replaced, not to one that still works. Staff brief the Board on readiness on December 2, 2026 and recommend further flexibilities, so check the Air District's building appliances page before planning around a date.

What outdoor temperatures should a Concord heat pump be sized for?

The Energy Code points to Joint Appendix JA2, which lists Concord at 95°F dry bulb and 67°F wet bulb for cooling and a 27°F winter median of extremes for heating, with indoor cooling at 75°F. If airflow is not field-verified at 350 cfm per ton, the code also limits how far capacity may exceed the calculated loads.

Can I replace a gas furnace with electric baseboard heaters in Concord?

Generally not as the main heat. Under Section 150.2(b), a replacement space heating system may not use electric resistance as the primary source unless the existing system is already electric resistance and either the new one is not ducted or no ducted cooling is being installed. A heat pump is the usual electric route instead.

Does a new system near Canyon Creek need a better air filter?

Any entirely new or complete replacement system must meet the mandatory filtration rule in Section 150.0(m)12, which calls for MERV 13 or better filters on systems supplying air to habitable rooms, designed for the filter's pressure drop at the design airflow. Ask for the filter rating and how the system accounts for that pressure drop.

Where these facts come from

Checked against these public sources in November 2026. Rules and programs change: confirm permit requirements with the city before work starts, and a contractor's license on the CSLB website.

Heat pump and HVAC work in Concord? Tell us what you see.

One request reaches local handymen and contractors who take this work. The Handyman SF connects you with them; it does not do the work.

HandymanNow for handymen Work in Concord? Get job leads by text. Pick your trades and areas, take only the jobs you want. No subscription. Start getting leads HandymanNow for homeowners Get the HandymanNow app. Send a request with photos, message your handyman and follow them on the way. Download the app

HandymanNow app

Fix it faster. Find work faster.

Homeowners send a job with photos and follow their handyman on the map. Handymen get local jobs by text and take only the ones they want.

Call WhatsApp (opens WhatsApp) Free quote